It is currently Sat Nov 23, 2024 9:57 pm


View unanswered posts | View active topics


Board index » 82 Collector Edition » 82 CE General Discussion

All times are UTC - 5 hours




Post new topic Reply to topic  Page 1 of 1
  [ 7 posts ] 
  Print view Previous topic | Next topic 
Author Message
tammyNtrish82CE
PostPosted: Fri Jun 13, 2008 11:30 pm 
Offline
Forum Member
Forum Member

Joined: Thu Jun 12, 2008 10:28 pm
Posts: 16
Location: Washington State
Hi,

We are new to the list so please excuse me if this has been discussed.

How do you get the hinges off the hatchback?

When we turn the connector from below the fastener just spins so we can't back it out.

We just bought our CE on 6/12, so we are just learning about the hatchback hinge issue. We had a tough time getting the hatch open. The hinges look like they spread about an inch from what I saw in a CAD drawing in an earlier post.

We will be posting our progress on the restoration at www.pfoust.com

Thanks, Tammy

_________________
We just bought an 82 CE Corvette and will be starting to restore it. We would love to share our project and learn from others!
Top
 Profile  
 
tammyNtrish82CE
PostPosted: Sun Jun 15, 2008 10:43 am 
Offline
Forum Member
Forum Member

Joined: Thu Jun 12, 2008 10:28 pm
Posts: 16
Location: Washington State
We found the installation instructions for Simpson36's hinges (we ordered a pair) and drilled out the screw and preserved the exterior button.

Tammy

_________________
We just bought an 82 CE Corvette and will be starting to restore it. We would love to share our project and learn from others!
Top
 Profile  
 
82ColEd
 Post subject:
PostPosted: Mon Jun 16, 2008 2:11 am 
Offline
Veteran Forum Member
Veteran Forum Member

Joined: Fri Oct 10, 2003 10:21 am
Posts: 377
Location: Frankfurt/Germany
Welcome to the 82 CE Registry to you both.

Cant wait to see pics of your car. 8)

Feel free to post any questions here, while we're small, people are friendly and helpfull..


Dont forget to add your car to the registry up the front, so we can keep track of them all..

_________________
Image
-Stefan
Top
 Profile  
 
Iron 82
 Post subject:
PostPosted: Fri Jun 20, 2008 8:29 pm 
Offline
Moderator
Moderator

Joined: Sat Dec 13, 2003 2:45 pm
Posts: 463
Location: Driving to paradise
Welcome to this site.

Glad you two are able to find the things you need to complete your fixings of your vette.

If you two need anything. Give a shout and we'll do our best in helping.

_________________
C3VR Lifetime Member # 51
NCM Lifetime Member #1353
Iron82
Top
 Profile  
 
fester
 Post subject:
PostPosted: Mon Jun 30, 2008 7:28 pm 
Offline
Forum Member
Forum Member

Joined: Tue Apr 24, 2007 7:54 pm
Posts: 21
Location: Blandon, PA
:) I've been rather fortunate with my hinges. So far all I had to do was take them off one at a time and use a clamp to squeeze them back. I took a measurement before and only had to squeeze them in about a 1/4" to 3/8". :x The biggest pain was the constant adjusting of the latch toward the back until I got it right. Now every time I pull the release the glass pops up no problem :D . Just take one small project at a time and hang in there.
Top
 Profile  
 
Iron 82
 Post subject:
PostPosted: Mon Jun 30, 2008 7:30 pm 
Offline
Moderator
Moderator

Joined: Sat Dec 13, 2003 2:45 pm
Posts: 463
Location: Driving to paradise
fester wrote:
:) I've been rather fortunate with my hinges. So far all I had to do was take them off one at a time and use a clamp to squeeze them back. I took a measurement before and only had to squeeze them in about a 1/4" to 3/8". :x The biggest pain was the constant adjusting of the latch toward the back until I got it right. Now every time I pull the release the glass pops up no problem :D . Just take one small project at a time and hang in there.


Congrates to your success. Keep rollin' on. :wink:

_________________
C3VR Lifetime Member # 51
NCM Lifetime Member #1353
Iron82
Top
 Profile  
 
WARRIOR2291
PostPosted: Wed Jul 02, 2008 7:27 am 
Offline
Veteran Forum Member
Veteran Forum Member

Joined: Tue Oct 03, 2006 9:57 am
Posts: 97
Location: Chipley Florida
tammyNtrish82CE wrote:
Hi,

We are new to the list so please excuse me if this has been discussed.

How do you get the hinges off the hatchback?

When we turn the connector from below the fastener just spins so we can't back it out.

We just bought our CE on 6/12, so we are just learning about the hatchback hinge issue. We had a tough time getting the hatch open. The hinges look like they spread about an inch from what I saw in a CAD drawing in an earlier post.

We will be posting our progress on the restoration at www.pfoust.com

Thanks, Tammy



Please go to this website and article, If you are looking to replace your hinges this will answer your question.

http://www.thecubestudio.com/CollectorE ... ctions.htm

_________________
updated
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 1
  [ 7 posts ] 

Board index » 82 Collector Edition » 82 CE General Discussion

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 26 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  

Original Replacement Car Auto Decals, Graphics, Stickers for GM, Mopar, Plymouth, Dodge, Ford and AMC; Trans Am, Formula, Firebird, Camaro, Z28, Corvette, El Camino, Chevy and Mustang.



Powered by phpBB® Forum Software © phpBB Group

Advertisements by Advertisement Management